Elektronikk

Endeknott for Switchcraft jackchassi - Gull

65,-

Dobbeltsporet endeknott for Switchcraft jack i akustisk gitar. Ekstra spor for feste av strengeholder. Kan brukes som reservedel for de som har mistet remfestet på jackchassi. US gjenget.

Fender American Vintage Jaguar® Mute System Foam Strip

77,-

Fender American Vintage Jaguar® Mute System Foam Strip, 3/8 x 1/4 (2)

Killswitch Potmeter - 250K

169,-

Kill Pot 250 KOhm for singlecoil mikrofoner. Spesialdesignet 250K LOG (Audiotaper) Split Shaft potmeter med innebygd heavy duty fjærbelastet push switch som bryter signalet når du trykker på potmeteret. Muliggjør rask "stuttering" uten elektroniske "knepp" eller kortslutningsstøy. Lengde på gjenget bøssing: 16mm

MEC dual potmeter med DPDT

225,-

Stacked Pot (05C250K/05A250K) cc. B500K Switch On/On push/pull DPDT

Potmeter m DPDT push push switch 250K - US gjenget

74,-

250K Audiotaper (LOG) potmeter med DTDP push push switch for f-eks. coil tapping, fasevending eller split funksjoner.Proff kvaliltet. Passer ikke metriske knotter men originale US knotter (Gibson/Fender). Viktige mål: 9mm gjengediameter 9mm lengde på gjenget skaft 26mm monteringsdybde (under plekterplate) 47mm total dybde

Emerson Premium PRO potmeter splitshaft 1MEG

123,-

Emerson Custom Premium Potentiometer - 1Meg, Short Split Shaft TAPER: AUDIO TAPER (20% PROPRIETARY EMERSON DESIGN) (20% OUTPUT @ ½ ROTATION) OHM VALUE: 1 MEG Ω TOLERANCE: +/- 8% TOLERANCE (920K - 1080K Ω) SHAFT LENGTH: 0.375” (9,5mm) FOR USE ON PICKGUARDS, CONTROL PLATES, AND THIN WOOD TOPS) SHAFT STYLE: SPLIT (FINE KNURLING - 24 SPLINE - FOR US SPEC CTS STYLE PUSH ON KNOBS) INCLUDED HARDWARE: 1 FLAT WASHER, 1 LOCK WASHER, 1 MOUNTING NUT PRODUCT NOTE: WORKS GREAT IN JAZZMASTERS OR OTHER SETUP THAT NEEDS A 1MEG SPLIT SHAFT POT. (FOR PUSH-ON KNOBS) New for 2024! The new Emerson pots are finally here. After 3 years of development, testing and research we are proud to announce the launch of the guitar pot we’ve always wanted to offer, but couldn’t… until now! The Emerson PREMIER PRO Pot. These completely new PREMIER PRO pots were designed by the founder and owner Mitch Ingram along with tons of help and technical knowledge from Jon Erickson at Tonecraft Audio. We have been offering our spec’d line of “Emerson PRO CTS pots” for many years, but when 2020 rolled around and supply chain disruptions created lead-times 20x the norm, it became clear that it was time to take matters into our own hands. Mitch was tired of accepting the industry norm that CTS pots are “good enough” or the “best” available and set out to create his own design and brand of in-house pots. The PREMIER PRO pots not only look familiar but are built with an incredibly consistent feel and function from lot to lot. It took a truckload of money, time and effort, but we believe that these new Emerson PREMIER PRO pots are the best guitar pots available… PERIOD. Unconstrained by an off the shelf menu of factory options, we designed and developed these pots from the ground up. We put extra care into all the fine details. Ideal taper, torque and tolerance is meticulously built-in and our unique lugs are designed specifically for point to point assembly; slightly oversized with plenty of room to run ground wires/buss wires and any other connection you need. We chose a robust Fiberglass substrate that the solder lugs and resistive track are mounted to. This material is exceptionally strong and won’t easily bend and snap like those in many other pots. The taper we used is a custom 20% Audio Taper and a proprietary design from Emerson. This taper works equally as well in the volume position as it does in the tone position. We designed and built the PREMIER PRO line of pots to be exceptionally rugged and reliable for the fine guitars they will function in. Emerson appreciates the support of players, builders and distributors around the world. We are proud to always push the levels of quality and craftmanship alongside you.

Potmeter 100K LIN CGE mini

25,-

100K lineær pot for elektronikk (f.eks. aktive instrument og pedaler) Measurements: Diameter= 16mm Bushing Threads = M8 Shaft: Split Shaft (18 Tooth) Bushing Length: Standard Bushing 9,5mm

Sprague Orange Drop Caps .1μF 100V

33,-

Proffkvalitet Orange Drop 215 series kondensator på 0,1mF - 100V . Fin til tonekontroll på bassgitar. Orange Drop 225P series Polyester film/foil capacitors, 100v, 10% tolerance. The 225P series capacitors in 100v rating are ideal for work in guitar wiring where a smaller footprint is needed to fit in the tight spaces often found in instrument control cavities. Features: Non- inductively wound polyester film/foil construction Radial lead 10% tolerance 100v voltage rating Rated for 85°C operation Tinned copper-clad steel leads

3 veis Telecaster type vender

38,-

Rimelig 3 veis swich som brukes som standard i rimelige gitarer. Kurant kvalitet

Fender Jazzmaster USA master control shield

250,-

Fender skjerming av masterkontollhulrom på Jazzmaster.

Låseskive for små potmeter

1,-

Låseskive til små potmeter. (USA: 3/8 in. Metric: 8 mm) Passer f.eks. de rimeligste potmeterne våre og Alpha potmeter som sitter i de fleste gitarer produsert i Østen. Pris er pr stk.

3 veis lukket vender - Japan

38,-

3-veis lukket mikrofonvender for Strat type gitarer . Produsert av Hosco i Japan og brukes for eksempel i gitarer fra Ibanez . Levers med 2 panhode festeskruer. Husk også å bestille knott til venderen om du ikke har det fra før.

Låseskive for M8 metriske potmeter

1,-

Låseskive til metriske potmeter med M8 potmeter bøssing. Pris er pr stk.

Fender® EVH® Wolfgang Neck - krom

1.254,-

Finally anyone can be a tinkerer! The highly sought after pickups and pots previously only available on the Wolfgang USA are now available to everyone. Wolfgang® Pickups include mounting hardware and wiring diagram.

Låseskive for M9 metriske potmeter

1,-

Låseskive til metriske potmeter med M9 (9mm) potmeter bøssing. Pris er pr stk.

ObsidianWire HH Strat

976,-

ObsidianWire Custom HH kit for Stratocaster® har komponenter som er matchet for å gi deg best mulig lyd. Du trenger ikke å lodde noe med dette settet. HH settet er for Strat med 2 humbuckere. Skal du utnytte funksjonaliteten med splitcoilvenderen i kit'et må du ha humbuckere med 4 ledere. PUSH PULL CONTROL DOWN 1: Bridge Humbucker in Full Mode 2: Bridge Humbucker + Neck Humbucke in Full Mode 3: Neck Humbucker in Full Mode PUSH PULL CONTROL UP 1: Bridge Humbucker in Single Coil Mode 2: Bridge Humbucker + Neck Humbucker in Single Coil Mode 3: Neck Humbucker in Single Coil Mode NB! Mutterene som sitter innerst på de gjengede potmeterskaftene skal ikke løsnes. De er der for at det skal bli tilstrekkelig avstand mellom komponetloddingene og skjermingsfolien (om du har det på din gitar.) ObsidianWire leveres med ferdiginstallert Custom Spec Treble Bleed Mod. Dette forhindrer at du mister topp når volumet på gitaren dempes. ObsidianWire slipper du å lodde for å koble til. Kablene fra mikrofonene kobles enkelt i kontaktene på elektronikken. Passer uten modifikasjon på American og Mexico Fender Strat. på Japan Fender og Squire må hullene i plekterbrettet typisk utvides til 10mm for å passe USA typen pga tykkelsen på bøssingene og potmeterskaftene.Du bør også skaffe deg ratt med US spec (24 tenner) for optimal passform på split shaft potmeterene. ObsidianWire Custom Select Pots (Crafted by CTS) (+/-6%) (Matched to +/-2%) SPLIT SHAFT Genuine Oak Grigsby Switch Genuine Switchcraft Output Jack ObsidianWire Custom Select 150 Series Polyester Film Capacitor (Hand Tested to +/-10%) ObsidianWire Premium Selected Volume Mod / Treble Bleed - Improved Volume Taper & Clarity Easy to Follow Install Manual Split your humbucker pickups into single coils, allowing for traditional Strat® tones, and back again with a push or pull of the volume control. (requires 4 conductor pickups) PUSH PULL CONTROL DOWN 1: Bridge Humbucker in Full Mode 2: Bridge Humbucker + Neck Humbucke in Full Mode 3: Neck Humbucker in Full Mode PUSH PULL CONTROL UP 1: Bridge Humbucker in Single Coil Mode 2: Bridge Humbucker + Neck Humbucker in Single Coil Mode 3: Neck Humbucker in Single Coil Mode

Fender® EVH® Wolfgang Neck - svart

3.199,-

Finally anyone can be a tinkerer! The highly sought after pickups and pots previously only available on the Wolfgang USA are now available to everyone. Wolfgang® Pickups include mounting hardware and wiring diagram.

Batteriklype for 9V batteri - horisontal

15,-

Klype for 9V batteri. Batteri og skruer medfølger ikke.

Batteriklype for 9V batteri - vertikal

18,-

Klype for 9V batteri. Batteri og skruer medfølger ikke.

Mutter for jack og potmeter - gull

3,-

Gull mutter til jack chassi med US gjenger som for eksempel Switchcraft. Passer også US potmeter fra CTS og CGE. Passer ikke metriske chassis eller potmeter. Pris er pr stk. Tommemål: "3/8-32 1/2""

ObsidianWire Custom Nashville Telecaster

894,-

SUPER EASY, SOLDER-LESS INSTALL All ObsidianWire Pro-Wired Electronics are super easy to install, and allow for solder-less pickup changes with ObsidianWire Plug, Play & Enjoy connectors. What is Nashville® Wiring? The Three Pickup Telecaster® Nashville wiring is a super popular Tele® mod that adds a third pickup between the traditional Telecaster® neck and bridge pickups. This gives you the standard 5-way control layout that you would usually find on a Stratocaster®. The trouble is that in gaining a middle pickup, and the cool Strat quack from the neck & middle pickup combo, you lose the traditional Telecaster neck and bridge pickup combo. THE SOLUTION: A 7-WAY CONTROL LAYOUT The ObsidianWire Custom Nashville 7-Way for Tele® adds a push pull switch to the tone control, which connects the neck pickup directly to the guitars volume control. This allows the possibility to play the neck and bridge pickups together again, or even all three pickups at once. "THE 7-WAY SWITCH IS BUILT IN TO THE TONE CONTROL, SO THERE IS NO NEED TO DRILL YOUR CONTROL PLATE. THIS WILL DROP RIGHT IN" '7-WAY' SWITCH MOD // FUNCTION '7 WAY' SWITCH ON (UP) '7 WAY' SWITCH OFF (DOWN) Bridge + Neck Bridge Bridge & Middle + Neck Bridge & Middle Middle+ Neck Middle Neck & Middle Neck & Middle Neck Neck CRYSTAL CLEAR TONE To make your tone crystal clear at lower volumes we also include an ObsidianWire Custom Spec Treble Bleed Mod. This prevents tone 'muddiness' at low volumes by allowing high frequencies to pass along a separate path to your amp, rather than being stopped short by the increasing resistance at the volume control. COMPONENTS Potentiometers: Obsidian Custom CTS Pots 250K (+/-10%) Solid Shaft 1/4" Capacitors: (150 Series Polyester Film 0.022uf) (+/-5%) Switch: Genuine Oak 5 Way Switch Jack: Pro-Wired Switchcraft J11 Mono COMPATIBILITY American series Fender® Nashville Telecasters - Direct Fit Mexican series Fender® Nashville Telecasters - Direct Fit Japanese Fender & Squiers 'Nashville' - You will need to purchase a genuine Fender USA control plate and new 1/4" knobs or ObsidianWire Control plate & Knobs Fits genuine Fender Tele Will not fit Squier or 'Metric' sized plates and knobs. Always Check Hole Layout Hole Size: 9.52mm (3/8”) Control Hole Spacing: 63mm (2.48") Knob Size: Solid Shaft 6.35mm (1/4") US SPEC Switch Tip: CRL/OAK type 1.32mm x 4.78mm (.052" x .188") Does NOT Fit: - Thinline Telecaster - G & L ASAT - May be fitted with adjustments to control slot size & new genuine Fender USA control plate and new 1/4" knobs or ObsidianWire Control plate & Knobs - Other Guitars - We cannot guarantee that these will fit any other guitar. Note: Aftermarket control plates will NOT fit. We recommend a genuine Fender control plate – Part Number: 099-2058-000 or equivalend Use US spec 1/4" Solid shaft controls. We recommend that you check your knobs are the correct size and replace them if necessary.

Potmeter solidshaft 50K REVERSE LOG

19,-

Reverse (Left Hand) Audiotaper 50K Potmeter. Låseskive og stoppskive følger med. Viktige mål: Total pot dybde - 30,5mm Lengde på gjenget bøssing - 10mm Bøssing diameter - 9,5mm Skaft diameter - 6mm Potmeterhus diameter - 23,7mm

Skive for jack og potmeter - gull

3,-

Gull skive til potmeter fra CTS og CGE. Passer også jack chassi.

5 veis lukket vender - Japan

38,-

5-veis lukket mikrofonvender for Strat type gitarer . Produsert av Hosco i Japan og brukes for eksempel i gitarer fra Ibanez . Levers med 2 panhode festeskruer. Husk også å bestille knott til venderen om du ikke har det fra før.

Potmeter 500K mini - splitshaft

18,-

500K minipotmeter fra Alpha. LOG Audiotaper. Metriske gjenger. Kort bøssing. 16mm diameter potmeterhus. Measurements: Diameter= 16mm Bushing Threads = M8 0.75 Resistance: 500 kohm Taper:Audio Taper Bushing Length: Short Bushing 1/4 in.

Skive for metriske M8 potmeter - nikkel

1,-

Nikkel skive til metriske M8 (8mm) potmeter.

MOD oil filled Caps .47uF 50V

116,-

Mod® Electronics Oil Caps are high quality, hand-crafted capacitors that are the perfect choice for guitars, amplifiers, and all audio equipment. Each capacitor is impregnated with mineral oil for a void-free winding providing highly stable capacitance. The capacitor is hermetically sealed in an aluminum casing to ensure a long life. The detailed construction results in a precise capacitance with a tolerance of ±10%. Mod® Oil Caps also feature a red stripe to designate the outside foil. The 50V series are in smaller packages that are perfect for guitars, effects and more. Casing: Hermetically sealed aluminum Dielectric: Mineral oil Lead Diameter: 20AWG Termination Style: Axial Tolerance: ±10% Value: .047 μF Voltage Rating: 50V

Caps 0,022μF

3,-

Billig standard kjeramisk kondensator på 0,022μF.

Caps 0,033μF

4,-

Billig standard kondensator på 0,033μF.

Mutter for Switchcraft vender - gull

13,-

Mutter til Switchraft vender med 15/32-32 gjenger (tommemål).

Mutter low profile for Switchcraft vender

9,-

Finriflet low profile mutter til Switchraft vender med 15/32-32 gjenger (tommemål).

Mutter low profile for Switchcraft vender - gull

9,-

Finriflet low profile mutter til Switchraft vender med 15/32-32 gjenger (tommemål).

Skrue for vender - metrisk - gull

6,-

Skrue for feste av 3,4, og 5-veis mikrofonvender. Denne har panhead (standard på Telecaster). Skruen er metrisk og passer ikke US vendere fra OAK eller CRL.

Skrue for vender - senkhode - svart

6,-

Skrue for feste av 3,4, og 5-veis mikrofonvender. Denne har senkhode.Skruen er metrisk og passer ikke US vendere fra OAK eller CRL.

Fender S-1 Switch Coupling Sleeve, Nylon

42,-

Original Fender® S-1™ nylon koblingshylse.

Skrue for vender - svart

6,-

Skrue for feste av 3,4, og 5-veis mikrofonvender. Denne har panhead (standard på Telecaster). Skruen er metrisk og passer ikke US vendere fra OAK eller CRL.

Skrue vintage for vender - nikkel

6,-

Skrue vintage for feste av 3,4, og 5-veis mikrofonvender. Denne har panhead (standard på Telecaster). Prisen er pr stk.

Glidebryter for Mustang og Duosonic - hvit

94,-

Switchcraft Glidebryter for Fender Mustang og Duosonic. Skruer følger med. Chassis dimensjon: 12.70mm x 44.45mm x 17.46mm Skrueavstand senter til senter: 35.72mm Dybde: 20.64mm Utsparring plekterbrett: 7.94mm x 20.64mm Electrical: Contact Ratings: Fine silver contacts rated at 3A, 300W maximum AC non-inductive load standard. Leakage Resistance: 1,000 MW or greater Dielectric Strength: 250 VDC Materials: Frame: Steel, plated Bushing and Shaft: Copper alloy, plated Springs: Copper alloy Knob: Molded thermoplastic Insulation: Rigid plastic spacers with plastic tubing through stack. Rigid plastic and/or thermoplastic lifters. Thermoplastic cam on actuator end This is a 3 position switch that can be wired as on/on/on or on/off/on.

Fender DPDT push-Push switch

75,-

DPDT Push Switch som brukes på bl.a. Fender Jeff Beck strat, Elite og endel andre Fender modeller. Selges uten knott som må bestilles for seg.

Warwick pute for Jazzbass mikrofon

31,-

Skumgummipute for montering under mikrofon på Jazzbass. - foam rubber for mounting underneath pickups - suitable for P-Style pickups - dimensions (L x W x H) 56 x 27 x 20 mm / 2.20" x 1.06" x 0.79" - adjust to required size by cutting off excess material - not recommended for instruments with nitro-cellulose finish

Warwick pute for MM4 mikrofon

31,-

Skumgummipute for montering under MusicMan style 4 strengs mikrofon. - foam rubber for mounting underneath pickups - suitable for 4-string MM-Style pickups - dimensions (L x W x H) 89 x 48 x 20 mm / 3.5" x 1.89" x 0.79" - adjust to required size by cutting off excess material - not recommended for instruments with nitro-cellulose finish

Warwick pute for MM5 mikrofon

31,-

Skumgummipute for montering under MusicMan style 5 strengs mikrofon. - foam rubber for mounting underneath pickups - suitable for 5-string MM-Style pickups - dimensions (L x W x H) 105 x 48 x 20 mm / 4.13" x 1.89" x 0.79" - adjust to required size by cutting off excess material - not recommended for instruments with nitro-cellulose finish

Warwick pute for P-bass mikrofon

31,-

Selvklebende skumgummipute for montering under mikrofon på P-Bass. Du trenger som regel to av denne for å skifte puter på en P-bass. - foam rubber for mounting underneath pickups - suitable for P-Style pickups - dimensions (L x W x H) 56 x 27 x 20 mm / 2.20" x 1.06" x 0.79" - adjust to required size by cutting off excess material - not recommended for instruments with nitro-cellulose finish

Potmeter m DPDT switch 250K - metrisk

133,-

250K Audiotaper (Log) potmeter med Push Pull DTDP switch for f-eks. coil tapping, fasevending eller split funksjoner.Proff kvaliltet. Passer metriske knotter med 18 tagger. Leveres med to muttere, låseskive og stoppskive. Ved bruk av ratt med settskrue anbefales konverteringshylse splitshaft-solidshaft. Viktige mål: 7,2 mm gjengediameter (M7) 9,5mm lengde på gjenget skaft 29mm monteringsdybde (under plekterplate) 47mm total dybde

Om oss

Meny

Totalt:

Søkeresultater

Elektronikk

Totalt:

Floyd Rose

Faber

Bridge

Plekterbrett

Elektronikk

Plekterbrett

Elektronikk

Plekterbrett

Elektronikk